AccountBasket (0)

ROSTRA
ROSTRA
ROSTRA
Demo control

ROSTRA

Ottavia Stovetop Espresso Maker

4.6128 reviews

€49.90 €57.00€59.90 €69.90€72.00 €82.00incl. VAT
Size

In stock — dispatched within 24 hours

Free delivery over €60 · 30-day returns · 2-year guarantee

  • Cast aluminium body, polished upper half
  • Eight facets, so it grips on the hob and on the hand
  • Heat-resistant handle and lid knob
  • Safety valve and replaceable seal
  • Made in Italy · not suitable for induction hobs

The Ottavia is the stovetop pot our grandmothers used, made the way it was made then: one piece of cast aluminium for the boiler, a turned and polished upper half, and a thread between them you tighten by hand. Water goes in the bottom, ground coffee in the basket, and the hob does the rest.

Eight facets are not decoration. They give the pot something to be gripped by when it is hot, and they keep it from turning on a gas hob. The handle and the lid knob are moulded in a heat-resistant compound that stays cool enough to hold.

In the box

  • Ottavia pot, 6 cups
  • One spare seal
  • Instructions and a first-use guide
  • Capacity — 3, 6 or 9 espresso cups (30 ml each)
  • Material — cast aluminium body, polished upper half, phenolic handle
  • Height — 190 mm (6-cup) · Weight — 420 g
  • Base — 95 mm · gas, electric and ceramic hobs
  • Seal — food-grade silicone, replaceable, sold separately
  • Care — hand wash only, no dishwasher
  • Reference — ROS-OTT-06 · Made in Italy

You may also like

End of the demonstration page. Nothing above is for sale.

What you just scrolled past

Your page, exactly as it is, plus one block.

Everything above is an ordinary product page — the layout you already have, the copy your team already wrote, the checkout you already trust. One element of it is real 3D, running on the graphics chip of the machine you are reading this on. Try the control at the top of the window.

Nothing else on this page changed. Not the layout, not the copy, not your checkout, not your CMS.

That sentence is the entire offer. Every other way of buying 3D assumes you are redoing a page — which means a budget line, a committee, and a date some months out. This assumes none of it. You keep your site, your CMS and your team, and one piece goes into one slot that already exists. It is the only 3D a head of e-commerce can decide on alone, out of money they already hold.

And it is not a video and not a spun sequence of photographs. The pot above is computed while you look at it: turn it with your finger or your mouse, and unscrew it into its two halves to see the basket, the seal and the perforated plate — the parts a photograph of a coffee pot can never show, and the ones a customer wonders about before they buy.

What it does not do to your page

Everything below was measured by this page, on this page, in your browser, while you were reading it.

No layout shift
measuring… cumulative layout shift for the whole document

The box is filled by the same response that carries the page, at its final size, before a single script runs. The canvas is laid over that image afterwards, inside the same box. Use the comparison control above and this line will measure it for you.

Loaded only when needed
measuring… transferred for the 3D engine

The engine is a separate chunk, requested only when the box comes near the screen — never part of the JavaScript your page loads to exist. On a machine that cannot render it, the request is never made at all: the check that decides is a few lines in the page’s own script.

Clean fallback
live, with the photograph underneath

With no WebGL, or under prefers-reduced-motion, the box keeps the still image and the page loses nothing — because that image is not a degraded state, it is the state your page already has. Try either one: reload with WebGL refused, with reduced motion, or back to normal. The engine is not fetched in either case — watch the line above.

No constraint on the rest
measuring…

Measured across the engine’s arrival: your document’s own touch-action is still —, your scroll position —, and the module registered —. Nothing else: no pointer, wheel, key or scroll handler anywhere but on its own canvas, and no rule of its own on any element it does not own.

The same block, dropped into

  • A product page — the main photograph becomes the object itself — the slot, the size and the rest of the page unchanged.
  • A manufacturer's catalogue — one reference per page, turned and taken apart, instead of a PDF nobody opens.
  • An option page — the finish, the size and the fitting shown on the part rather than described beside it.
  • An article or a technical explainer — one figure in the middle of the text that the reader can turn while they read it.
  • A customer area behind a login — the machine your client owns, with its parts named, so a support call begins with both of you looking at the same thing.

How it goes

  1. You send me the page and the object.
  2. I build the object and its box, and send you a link you can open in your own browser and show to whoever needs to see it.
  3. One tag goes into your page — by your developer, or by me with them. An afternoon, not a quarter.

from €1,500, typically €2,500–5,000 for one block, including integration into your existing page.

The range moves with the object: a pot with two parts sits at the bottom of it, a machine with a dozen named components at the top. If you already have CAD, most of that work disappears.

Tell me which page

Send me the URL of the page you are thinking of. You will get back a straight answer about whether the object suits this treatment, what it would cost, and how long it would take — not a proposal deck.

One reply, from me, within one working day. No newsletter, no sequence.